Hidden water leak detection in Al Taawn, Jeddah: cost & published offers

Prepared by the technical team · editorial review · last updated 13 November 2026 · Sources

Before we start: what we know about Al Taawn

The centre of Al Taawn is at 21.3509, 39.2697, about 23.6 km from the centre of Jeddah, with an approximate radius of 1.2 km. The approximate area shown on the map is centred here. The nearest wadi channel is about 0.9 km from the centre of Al Taawn (OpenStreetMap).

Main roads in or near Al Taawn: Al Laith Road. Al Taawn is about 10 km from the sea coast (OpenStreetMap).

The centre of Al Taawn sits about 25 m above sea level (SRTM open elevation data).

Hidden water leaks in Al Taawn, Jeddah, are first checked against the local setting, because the district's location shapes how water moves and where it tends to show up. The centre of Al Taawn sits at 21.3509, 39.2697, about 23.6 km from the centre of Jeddah, with an approximate radius of 1.2 km. The area lies about 25 m above sea level and is roughly 10 km from the sea coast, so technicians begin by considering how pipework and tanks in this elevation band are typically arranged and how pressure behaves across the local network. The nearest wadi channel runs about 0.9 km from the centre of Al Taawn, which is a reason to look carefully at ground moisture, soil movement and drainage paths near lower boundaries of the property, since nearby channels can affect the ground around buried lines.

Other matters are left to the site visit itself. The exact route of concealed pipes, the condition of joints and fittings, the presence of any slab or wall moisture, and the state of storage tanks cannot be judged from a map. A technician will walk the property, listen and check readings on the spot, and decide which sections need closer inspection. Where a tank is involved, the internal condition matters a great deal: internal coating is priced at SAR 25–65 per m², and the surface area and condition found during the visit will determine how that range applies to the job. Nothing about the cost of a particular repair should be assumed before the visit has confirmed what is actually there.

Finally, some information helps the technician work efficiently. Note when the problem was first noticed, whether the water bill has risen, where damp patches or unusual sounds appear, and whether the leak seems to change with the time of day or with use of taps and appliances. Record the age of the building, any previous repairs, and the location of known shut-off valves and tanks. Clear access to roofs, shafts, basements and plant areas saves time. Share these details before the visit so the first inspection can focus on the most likely sources of the leak.

Prices shown on this page come from our own published price list for the city; the final price is set after inspection.

Signs worth paying attention to

The following signs are worth checking before they grow:

• A damp patch that slowly grows on a wall or ceiling
• A hissing or trickling sound in the wall after the taps are off
• The meter keeps turning with every tap closed
• A water bill higher than usual with no change in use

Causes we see in the field

• A hot line that expands and contracts with use — we check this before anything else.
• A corroded joint inside a wall — we check this before anything else.
• A cracked pipe under floor tiles.

Tools and methods, and when we use them

How the work is done, step by step

1. Meter test: We stop all use and watch the meter to confirm whether water is actually being lost.
2. Line isolation: We close valves one line at a time to see which line loses pressure.
3. Acoustic listening: We follow the sound of water escaping under pressure and compare its strength between points.
4. Thermal imaging and moisture mapping: We map how far the wet area spreads behind paint and tiles.
5. Documentation: Readings, photos and the likely position go into a written report.

Quick comparison: facts and costs in Al Taawn

Short answers for Al Taawn

What we advise against

• Repainting the stain while the moisture keeps coming back
• Breaking tiles at random before the line is identified

What you receive

You receive: a technical report with the readings, the likely leak position and a confidence level, in a technical report with a verification code.